R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
XT 400
For Occasional Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
Copyright E2003 Electrolux Home Products, Inc.
530163440
4/23/03
CUTTING SAFETY
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swellings. Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ical attention. An anti--vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
WARNING: Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage the trimmer head and be thrown
causing serious injury.
S Use only for trimming, scalping, mowing, edg-
ing and sweeping. Do not use for pruning or
hedge trimming.
S Keep firm footing and balance. Do not over-
reach.
S Keep all parts of your body away from muffler
and spinning line. Keep engine below waist
level. A hot muffler can cause serious burns.
S Cut from your right to your left. Cutting on left
side of the shield will throw debris away from
the operator.
S Use only in daylight or good artificial light.
S Use only for jobs explained in this manual.
TRANSPORTING AND STORAGE
S Allow engine to cool; secure unit before stor-
ing or transporting in vehicle.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equipped with a spark arresting screen. If you
operate in a locale where such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal
homeowner use, the muffler and spark arrest-
ing screen will not require any service. After
S Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the carbure-
tor by starting the engine and letting it run until
it stops.
S Store unit and fuel in area where fuel vapors
cannot reach sparks or open flames from wa-
ter heaters, electric motors or switches, fur-
naces, etc.
S Store unit so line limiter blade cannot acciden-
tally cause injury. The unit can be hung by the 50 hours of use, we recommend that your
tube.
muffler be serviced or replaced by your autho-
rized service dealer.
S Store unit out of reach of children.
ASSEMBLY
NOTE: Knob must be assembled on the
right hand side of the unit as shown in the il-
lustration.
WARNING: If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the
empty fuel tank.
Finding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
ATTACHING THE ASSIST HANDLE
NOTE: Be sure to attach the assist handle to
the unit before attaching the shield.
2. Make sure the bolt is seated in the hex--
shaped hole in the handle.
3. Pivot the handle to a comfortable position.
4. Tighten knob securely.
ATTACHING SHIELD
WARNING: The shield must be prop-
erly installed. The shield provides partial protec-
tion from the risk of thrown objects to the opera-
tor and others and is equipped with a line limiter
blade which cuts excess line to the proper
length. The line limiter blade (on underside of
shield) is sharp and can cut you.
For proper orientation of shield, see KNOW
YOUR TRIMMER illustration in OPERATION
section.
1. Assemble handle to the unit as shown;
make sure bottom of handle is seated in
the groove in the trigger housing.
Groove
3
1. Remove wing nut from shield.
2. Insert bracket into slot as shown.
3. Pivot shield until bolt passes through hole in
bracket.
Slot
Shield
4. Securely tighten wing nut onto bolt.
Bracket
Wing
Nut
KN
REIT.
Cntrols
an
M
ON/OFF SWITCH
CHOKE
The ON/OFF switch is used to stop engine.
Move the switch to the OFF position to stop en-
gine.
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving the choke lever to the FULL CHOKE
position. After the engine attempts to start, move
the choke lever to the HALF CHOKE position.
Once engine has started, move the choke lever
to the OFF CHOKE position.
PRIMER BULB
The PRIMER BULB removes air from the car-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.
mixed with a good quality synthetic 2-cycle
air-cooled engine oil designed to be mixed at a
ratio of 40:1. Poulan/Weed Eater brand
synthetic oil is recommended. Mix gasoline and
oil at a ratio of 40:1. A 40:1 ratio is obtained by
mixing 3.2 ounces (95 ml) of oil with 1 gallon (4
liters) of unleaded gasoline. DO NOT USE
automotive oil or boat oil. These oils will cause
engine damage. When mixing fuel, follow
instructions printed on container. Once oil is
added to gasoline, shake container momentarily
to assure that the fuel is thoroughly mixed.
BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you
begin. If you do not understand the safety
rules, do not attempt to fuel your unit. Call
1-800-554-6723.
FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling.
This engine is certified to operate on unleaded Always read and follow the safety rules relating
gasoline. Before operation, gasoline must be to fuel before fueling your unit.
4
6. Pull starter rope handle sharply until engine
sounds as if it is trying to start, but do not
pull rope more than 6 times.
7. As soon as engine sounds as if it is trying to
start, move choke lever to HALF CHOKE
position.
8. Pull starter rope sharply until engine runs,
but no more than 6 pulls.
NOTE: If the engine doesn’t start after 6
pulls (at the HALF CHOKE position),
move the choke lever to the FULL
CHOKE position and press the primer
bulb 6 times. Squeeze and hold the
throttle trigger and pull the starter rope 2
more times. Move the choke lever to the
HALF CHOKE position and pull the start-
er rope until the engine runs, but no more
than 6 pulls. If the engine still doesn’t
start, it is probably flooded. Proceed to
STARTING A FLOODED ENGINE.
9. Once the engine starts, allow it to run 10
seconds, then move the choke lever to
the OFF CHOKE position. Allow the unit
to run for 30 more seconds at OFF
CHOKE before releasing the throttle trig-
ger.
IMPORTANT
Experience indicates that alcohol blended fuels
(called gasohol or using ethanol or methanol)
can attract moisture which leads to separation
and formation of acids during storage. Acidic
gas can damage the fuel system of an engine
while in storage. To avoid engine problems,
empty the fuel system before storage for 30
days or longer. Drain the gas tank, start the en-
gine and let it run until the fuel lines and carbure-
tor are empty. Use fresh fuel next season.
Never use engine or carburetor cleaner prod-
ucts in the fuel tank or permanent damage may
occur. See the STORAGE section for addi-
tional information.
HOW TO STOP YOUR UNIT
S To stop the engine, move the ON/OFF
switch to the OFF position.
S If engine does not stop, move choke to the
FULL CHOKE position.
Engine
ON/OFF
Switch
Choke Lever
HALF
FULL
OFF
NOTE: If engine dies with the choke le-
ver in the OFF CHOKE position, move
the choke lever to the HALF CHOKE
position and pull the rope until engine
runs, but no more than 6 pulls.
HOW TO START YOUR UNIT
STARTING A WARM ENGINE
1. Move ON/OFF switch to the ON position.
2. Move the choke lever to the HALF CHOKE
position.
3. Squeeze and hold the throttle trigger. Keep
throttle trigger fully squeezed until the en-
gine runs smoothly.
WARNING: The trimmer head will
turn while starting the engine. Avoid any con-
tact with the muffler. A hot muffler can cause
serious burns.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
4. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
5. Allow engine to run 15 seconds, then move
Starting Position
the choke lever to OFF CHOKE.
NOTE: If engine has not started, pull starter
rope 5 more pulls. If engine still does not run, it
is probably flooded.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
the choke lever in the OFF CHOKE position;
then, pull the rope to clear the engine of ex-
cess fuel. This could require pulling the starter
handle many times depending on how badly
the unit is flooded.
If the unit still doesn’t start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723.
1. Set unit on a flat surface.
2. Move ON/OFF switch to the ON position.
3. Slowly press the primer bulb 6 times.
4. Move choke lever to the FULL CHOKE
position.
5. Squeeze the throttle trigger fully and hold
through all remaining steps.
Starter Handle
Choke
Lever
Muffler
Primer Bulb
5
If the line is worn down to 2 inches (5 cm) or
less, more than one tap will be required to ob-
tain the most efficient line length.
OPERATING INSTRUCTIONS
OPERATING POSITION
ALWAYS WEAR:
Eye Protection
WARNING: Use only 0.080” (2 mm)
diameter line. Other sizes and shapes of line
will not advance properly and will result in im-
proper cutting head function or can cause se-
rious injury. Do not use other materials such
as wire, string, rope, etc. Wire can break off
during cutting and become a dangerous mis-
sile that can cause serious injury.
Long Pants
Heavy Shoes
CUTTING METHODS
Cut from your right to your left.
WARNING: Use minimum speed
and do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, etc.),
which can damage the trimmer head, become
entangled in the line, or be thrown causing a
serious hazard.
S The tip of the line does the cutting. You will
achieve the best performance and mini-
mum line wear by not crowding the line into
the cutting area. The right and wrong ways
are shown below.
WARNING: Always wear eye protec-
tion. Never lean over the trimmer head.
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness or other
serious injury.
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise and
vibration. The cutting line will last longer and will
be less likely to “weld” onto the spool.
Tip of the Line
Line Crowded Into
Does The Cutting Work Area
Always release the throttle trigger and allow the
engine to return to idle speed when not cutting.
To stop engine:
S Release the throttle trigger.
S Move the ON/OFF switch to the OFF posi-
tion.
TWIST AND EDGE
Wrong
S The line will easily remove grass and
weeds from around walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences. To
help avoid damage especially to delicate
vegetation or trees with tender bark,
shorten line to 4--5 inches (10--13 cm) and
use at less than full throttle.
The Twist and Edge feature allows for easy
edging of sidewalks, patios, driveways, etc.
1. Pull the tab toward the engine.
2. Twist the tube to the edging position; re-
lease tab.
S For trimming or scalping, use less than full
throttle to increase line life and decrease
head wear, especially:
S During light duty cutting.
S Near objects around which the line can
wrap such as small posts, trees or fence
wire.
TRIMMER LINE ADVANCE
S For mowing or sweeping, use full throttle for
The trimmer line will advance approximately 2
in. (5 cm) each time the bottom of the trimmer
head is tapped on the ground with the engine
running at full throttle.
a good clean job.
TRIMMING -- Hold the bottom of the trimmer
head about 3 inches (8 cm) above the ground
and at an angle. Allow only the tip of the line to
make contact. Do not force trimmer line into
work area.
The most efficient line length is the maximum
length allowed by the line limiter.Always keep
the shield in place when the tool is being oper-
ated.
Trimming
To advance line:
S Operate the engine at full throttle.
S Hold the trimmer head parallel to and above
the grassy area.
S Tap the bottom of the trimmer head lightly
on the ground one time. Approximately 2 in.
(5 cm) of line will be advanced with each
tap.
Always tap the trimmer head on a grassy
area. Tapping on surfaces such as concrete
or asphalt can cause excessive wear to the
trimmer head.
3 inches (8 cm)
above ground
SCALPING -- The scalping technique re-
moves unwanted vegetationdown to the
ground. Hold the bottom of the trimmer head
about 3 in. (8 cm) above the ground and at an
6
angle. Allow the tip of the line to strike the the surfaces being swept and move the tool
ground around trees, posts, monuments, etc. from side to side.
This technique increases line wear.
Swee
Scalping
MOWING -- Your trimmer is ideal for mowing
EDGING-- Adjust trimmer to the edging posi-
in places conventional lawn mowers cannot
tion (see TWIST AND EDGE section). Allow
reach. In the mowing position, keep the line
only the tip of the line to make contact. Do not
parallel to the ground. Avoid pressing the
force trimmer line into work area.
head into the ground as this can scalp the
ground and damage the tool.
Edging
Mowing
SWEEPING -- The fanning action of the rotat-
ing line can be used for a quick and easy
clean up. Keep the line parallel to and above
MAINTENANCE
CLEAN AIR FILTER
WARNING: Disconnect the spark
plug before performing maintenance except
for carburetor adjustments.
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
S Housing Screws
S Assist Handle Screws
S Debris Shield
1. Clean the cover and the area around it to
keep dirt from falling into the carburetor
chamber when the cover is removed.
2. Remove parts as illustrated.
NOTE: To avoid creating a fire hazard or
producing harmful evaporative emissions, do
not clean filter in gasoline or other flammable
solvent.
CHECK FOR DAMAGED OR
WORN PARTS
3. Wash the filter in soap and water.
4. Allow filter to dry.
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S ON/STOP Switch -- Ensure ON/STOP
switch functions properly by pushing and
releasing the switch. Make sure engine
stops. Wait 5 seconds before attempting to
restart unit to allow switch to reset. Restart
engine and continue.
5. Add a few drops of oil to the filter; squeeze
the filter to distribute oil.
6. Replace parts.
er
Screws
S Fuel Tank -- Discontinue use of unit if fuel
tank shows signs of damage or leaks.
S Debris Shield -- Discontinue use of unit if
debris shield is damaged.
Air Filter Cover
REPLACE SPARK PLUG
Replace the spark plug each year to ensure
the engine starts easier and runs better. Set
spark plug gap at 0.025 inch. Ignition timing is
fixed and nonadjustable.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and dis-
card.
INSPECT AND CLEAN UNIT AND
LABELS
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
labels using a damp cloth with a mild deter-
gent.
S Wipe off unit with a clean dry cloth.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
socket wrench.
4. Reinstall the spark plug boot.
7
SERVICE AND ADJUSTMENTS
10. Pull the lines extending outside of the hub to
LINE REPLACEMENT
release the lines from the notches.
1. Remove spool by firmly pulling on tap
button.
CARBURETOR ADJUSTMENT
2. Clean entire surface of hub and spool.
3. Replace with a pre-wound spool, or cut two
lengths of 12-1/2 feet of 0.080! (2 mm) di-
ameter Weed Eaterr brand line.
WARNING: Keep others away when
making idle speed adjustments. The trimmer
head will be spinning during this procedure.
Wear your protective equipment and observe
all safety precautions.
The carburetor has been carefully set at the
factory. Adjustments may be necessary if you
notice any of the following conditions:
S Engine will not idle when the throttle is re-
leased.
WARNING: Never use wire, rope,
string, etc., which can break off and become a
dangerous missile.
4. Insert ends of the lines about 1/2 inch (1
cm) into the small holes on the inside of
spool.
Make adjustments with the unit supported so
the cutting attachment is off the ground and
will not make contact with any object. Hold
the unit by hand while running and making ad-
justments. Keep all parts of your body away
from the cutting attachment and muffler.
Small
Holes
Spool
Idle Speed Adjustment
Allow engine to idle. Adjust speed until engine
runs without stalling (idle speed too slow).
S Turn idle speed screw clockwise to in-
crease engine speed if engine stalls or dies.
S Turn idle speed screw counterclockwise to
decrease engine speed.
Line exit holes
Line in Notch
Line in Notch
Hub
Idle Speed
Screw
5. Wind the line evenly and tightly onto the
spool. Wind in the direction of the arrows
found on the spool.
6. Push the lines into the notches, leaving 3 to
5 inches (7 -- 12 cm) unwound.
Air Filter
Cover
7. Insert the lines into the exit holes in the hub If you require further assistance or are unsure
as shown in the illustration.
about performing this procedure, contact an
authorized service dealer or call
8. Align the notches with the line exit holes.
9. Push spool into hub until it snaps into place. 1--800--554--6723.
STORAGE
S Clean the entire unit before lengthy storage.
S Store in a clean dry area.
S Lightly oil external metal surfaces.
WARNING: Perform the following
steps after each use:
S Allow engine to cool, and secure the unit
before storing or transporting.
FUEL SYSTEM
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
Under FUELING ENGINE in the OPERA-
TION section of this manual, see message la-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container. Fol-
low the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.
S Store unit and fuel well out of the reach of
children.
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
8
ENGINE
OTHER
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
S Do not store gasoline from one season to
another.
the spark plug opening. Slowly pull the S Replace your gasoline can if it starts to rust.
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range.
S Clean air filter.
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S At the beginning of the next season, use
only fresh fuel having the proper gasoline to
oil ratio.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing all of the
recommended remedies below except remedies that require operation of the unit.
REMEDY
TROUBLE
CAUSE
Engine will not
start.
1. ON/OFF switch in OFF
position.
1. Move ON/OFF switch to ON.
2. Engine flooded.
2. See “Starting a Flooded Engine” in
Operation Section.
3. Fuel tank empty.
4. Spark plug not firing.
5. Fuel not reaching
carburetor.
3. Fill tank with correct fuel mixture.
4. Install new spark plug.
5. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
6. Carburetor requires
adjustment.
6. Contact an authorized service dealer.
Engine will
not idle
properly.
1. Carburetor requires
adjustment.
2. Crankshaft seals worn.
3. Compression low.
1. See “Carburetor Adjustment” in
Service and Adjustments Section.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer.
1. Air filter dirty.
1. Clean or replace air filter.
2. Clean or replace plug
and regap.
Engine will not
accelerate,
lacks power,
or dies under
a load.
2. Spark plug fouled.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
5. Compression low.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
Engine
1. Choke partially on.
2. Fuel mixture incorrect.
1. Adjust choke.
2. Empty fuel tank and refill with
correct fuel mixture.
smokes
excessively.
3. Air filter dirty.
4. Carburetor requires
adjustment.
3. Clean or replace air filter.
4. Contact an authorized service dealer.
1. See “Fueling Engine” in Operation
section.
2. Replace with correct spark plug.
3. Contact an authorized service dealer.
Engine runs
hot.
1. Fuel mixture incorrect.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
4. Contact an authorized service dealer.
9
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
not cover predelivery setup or normal
warrants to the original purchaser that each new adjustments explained in the instruction manual.
Weed Eaterr brand gasoline tool or attachment
is free from defects in material and
workmanship and agrees to repair or replace
under this warranty any defective gasoline
product or attachment as follows from the
original date of purchase.
2 YEARS -- Parts and Labor, when used for
household purposes.
60 DAYS -- Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS -- Parts and Labor, if used for rental WARRANTY LASTS OR THE EXCLUSION
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use of
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES
EXCEPT
THOSE
EXPRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED
OR LIMITATIONS OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS OR EXCLUSION
MAY NOT APPLY TO YOU.
accessories and/or attachments not specifically The policy of ELECTROLUX HOME
recommended by ELECTROLUX HOME PRODUCTS, INC., is to continuously improve
PRODUCTS, INC., for this tool. Additionally, its products. Therefore, ELECTROLUX HOME
this warranty does not cover tune--ups, spark PRODUCTS, INC., reserves the right to
plugs, filters, starter ropes, starter springs, change, modify, or discontinue models,
cutting line, or rotating head parts that will wear designs, specifications, and accessories of all
and require replacement with reasonable use products at any time without notice or obligation
during the warranty period. This warranty does to any purchaser.
U.S. EPA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGA-
failure to ensure the performance of all sched-
TIONS: The U. S. Environmental Protection uled maintenance. As the small off--road en-
Agency and ELECTROLUX HOME PROD- gine owner, you should be aware that ELEC-
UCTS, INC., are pleased to explain the emis- TROLUX HOME PRODUCTS, INC., may deny
sions control system warranty on your year you warranty coverage if your small off--road
2002--2004 small off--road engine. ELECTRO- engine or a part of it has failed due to abuse, ne-
LUX HOME PRODUCTS, INC., must warrant glect, improper maintenance, unapproved mod-
the emission control system on your small off-- ifications, or the use of parts not made or ap-
road engine for the periods of time listed below proved by the original equipment manufacturer.
provided there has been no abuse, neglect, or You are responsible for presenting your small
improper maintenance of your small off--road off--road engine to an ELECTROLUX HOME
engine. Your emission control system includes PRODUCTS, INC., authorized repair center as
parts such as the carburetor and the ignition soon as a problem exists. Warranty repairs
system. Where a warrantable condition exists, should be completed in a reasonable amount of
ELECTROLUX HOME PRODUCTS, INC., will
time, not to exceed 30 days. If you have any
repair your small off--road engine at no cost to questions regarding your warranty rights and re-
you. Expenses covered under warranty include sponsibilities, you should contact your nearest
diagnosis, parts and labor. MANUFACTUR-
ER’S WARRANTY COVERAGE: If any emis-
authorized service center or call ELECTRO-
LUX HOME PRODUCTS, INC., at
sions related part on your engine (as listed un- 1--800--554--6723.
WARRANTY
COM-
der Emissions Control Warranty Parts List) is
MENCEMENT DATE: The warranty period be-
defective or a defect in the materials or work- gins on the date the small off--road engine is
manship of the engine causes the failure of such purchased. LENGTH OF COVERAGE: This
an emission related part, the part will be repaired warranty shall be for a period of two years from
or replaced by ELECTROLUX HOME PROD-
the initial date of purchase. WHAT IS COV-
UCTS, INC. OWNER’S WARRANTY RE-
ERED: REPAIR OR REPLACEMENT OF
SPONSIBILITIES: As the small off--road en- PARTS. Repair or replacement of any war-
gine owner, you are responsible for the
ranted part will be performed at no charge to the
performance of the required maintenance listed owner at an approved ELECTROLUX HOME
in your instruction manual. ELECTROLUX
HOME PRODUCTS, INC., recommends that
PRODUCTS, INC., servicing center. If you
have any questions regarding your warranty
you retain all receipts covering maintenance on rights and responsibilities, you should contact
your small off--road engine, but ELECTROLUX your nearest authorized service center or call
HOME PRODUCTS, INC., cannot deny war-
ELECTROLUX HOME PRODUCTS, INC., at
ranty solely for the lack of receipts or for your 1--800--554--6723. WARRANTY PERIOD: Any
10
warranted part which is not scheduled for re- use of add--on or modified parts. HOW TO FILE
placement as required maintenance, or which is A CLAIM: If you have any questions regarding
scheduled only for regular inspection to the ef- your warranty rights and responsibilities, you
fect of “repair or replace as necessary” shall be should contact your nearest authorized service
warranted for 2 years. Any warranted part which center or call ELECTROLUX HOME PROD-
is scheduled for replacement as required main- UCTS, INC., at 1--800--554--6723. WHERE TO
tenance shall be warranted for the period of time GET WARRANTY SERVICE: Warranty ser-
up to the first scheduled replacement point for vices or repairs shall be provided at all ELEC-
that part. DIAGNOSIS: The owner shall not be TROLUX HOME PRODUCTS, INC., service
charged for diagnostic labor which leads to the centers. Call 1--800--554--6723. MAINTE-
determination that a warranted part is defective NANCE, REPLACEMENT AND REPAIR OF
if the diagnostic work is performed at an ap- EMISSION RELATED PARTS: Any ELEC-
proved ELECTROLUX HOME PRODUCTS,
INC., servicing center. CONSEQUENTIAL
DAMAGES: ELECTROLUX HOME PROD-
TROLUX HOME PRODUCTS, INC., approved
replacement part used in the performance of
any warranty maintenance or repair on emis-
UCTS, INC., may be liable for damages to other sion related parts will be provided without
engine components caused by the failure of a charge to the owner if the part is under warranty.
warranted part still under warranty. WHAT IS EMISSION CONTROL WARRANTY PARTS
NOT COVERED: All failures caused by abuse,
neglect, or improper maintenance are not cov- (covered up to maintenance schedule), Ignition
ered. ADD--ON OR MODIFIED PARTS: The Module. MAINTENANCE STATEMENT: The
LIST: Carburetor, Ignition System: Spark Plug
use of add--on or modified parts can be grounds owner is responsible for the performance of all
for disallowing a warranty claim. ELECTRO- required maintenance as defined in the in-
LUX HOME PRODUCTS, INC., is not liable to
cover failures of warranted parts caused by the
struction manual.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
11
|